8 Channels 960H Hard Disk Car Mobile DVR Lightweight English /
High definition real-time recording with 8 x analog cameras or 4
x720p/1080p IP camera ,IPC:12V power supply;
Synchronized 8 channels video & 2 channels audio recording and
8 channels 960H Full frame recording;
Built-in 2.5 inch hard disk, 2TB storage, excellent shock
Build-in G-sensor module,GPS module,3G/4G module and wifi
Built-in 1 SD card slot for data backup in case of hard disk drive
error(need with 3G/4G module);
8 seconds delay power-off for data protection;
Support hard disk automatic heating,Operating temperature -40℃ ~
8V-36V wide voltage power supply,support POE.
Dimension(L×M×H): 192×184×61 mm.
Product Technical parameters:
|System||Language||English / Chinese|
|Operation Interface||Graphical menu operation interface(OSD menu)|
|Password security||Permissions setting of administrator & user|
|Video||Video input||8 channels, support CIF/HD1/D1/960H camera|
|4 x RJ45, support IPC camera with maximum of 1080P|
3 channels (1 x HDMI , 2 x CVBS,1 as φ3.5 Phone Jack, 1 in the
|Video display||Single picture, 4 pictures|
|Signal system||PAL / NTSC|
|Image compression||H.264 Main profile|
|Audio||Audio input||8 channels|
|Audio output||2 channels (1 as φ3.5 Phone Jack, 1 in the 24pin connector)|
|Record format||Synchroniz ed video & au dio recording|
|Recording&||Video resolution||Support 8 channels CIF/HD1/D1/960H camera Video input|
Support 8 channels 960H+4 channels IP camera Hybrid Video input
(Coming in soon)
| ||Video coding||ISO14496-10|
| ||Video bit rate||CIF: 1536Kbps ~ 128Kbps,|
| ||D1: 2048Kbps ~ 400Kbps,|
| ||960H: 2048Kbps ~ 400Kbps,|
| ||8 grades of image quality optional, Grade1 as best, Grade8 as
| ||Audio bit rate||8KB/s|
Up to 2TB HDD/SSD and 1 SD card for backup (with 3G/4G module
8 channels, alarm activated by low voltage (＜1V) or high
|Alarm output||1 channel, 12V output|
| ||RJ45 network|| |
Built-in 3G (HSUPA / HSDPA / WCDMA / EVDO / TD-SCDMA) module
|Communication||4G||Built-in 4G(TDD-LTE / FDD-LTE) module optional|
| ||Wi-Fi||Built-in Wi-Fi( 2.4 / 5.8 Ghz) optional|
|GPS||Built-in GPS module. Real-time geographic coordinates, speed
|Software||PC playback||Video files playback in PC with analysis of the vehicle status|
|CMSV6||Wireless real-time video & audio monitoring, GPS, alarm, etc.|
|Software||Upgrade through the front USB2.0 & hard disk|
Input voltage:＋8V～＋36V, When long-term under 8V, or long-term over
36V, Auto power off, enter protected mode.
Power-off working time
If main power supply is off, MDVR can continue running 8 seconds.
If connect built-in Patent UPS power-supply, MDVR can continue
running 30 minutes.
Vehicle key signal
Video input impedance
75Ω for each video input impedance
Video output Volt
Input 2Vp-p CVBS analog signal, reveal device input need 75Ω
impedance to fit
Low level alarm
High level alarm
Negative voltage alarm
Under well-ventilated environment condition.
186(W)mm x 61(H) x 192(L)mm
Product work diagram:
Our mobile DVR and car cameras have been got great effect from over
all the world!
Our mobile DVR and car cameras have had a great contribution for
Government and Policeman in Australia!
Remote view in real time recording on Iphone/Ipad/Android phone/PC
once MDVR is built-in 3G.
UPS battery support 1 hour after power off
Playback all video file and GPS tracking(Playback Analysis
Center Management Software:
CMSViewer(remote view in realtime recording once mobile DVR is
Remote live view via website/internt for FLV format
Q: What can I do when I found a problem with the product, but I can
not solve it by myself?
A: Take note of the model and software version number, then submit
a detailed description of the problem to the technical supporting
engineers to analyze; the more detailed you have submitted, the
more convenient for us to analysize.
Q: How about when there is no video output from the vehicle host
A: 1.Check the host’s turn-on status, if only a blue light on, it
means the host is in standby status and has not been started up
yet, meanwhile check whether the host’s power cords red &
yellow cords are in power supply status or not, if only one cord is
supplying power, the device is unable to start up.
2.Check the power supply status of display screen, as well as check
whether the display video has been switched to AV status.
3 Check the connecting status between the host’s video output cable
and display screen.
4 check whether the lock status of the host’s LOCK, it must be
locked before normal starting up.
Q: How to do when the car host video input interface is different
from the camera output interface?
A: The car uses 4PIN type while camera uses BNC or aviation head
type, if not in correspondence, please use conversion head for
connection or wiring based on standard corresponding according to
the cable sequence defined by the car host.
Q: How to do when the device does not conduct video recording after
it is turned on and SD card has already been installed?
A: 1.Check whether the SD card has been formatted or not after
installation, because unformatted SD card cannot be used. Enter
System Menu - System Tools - Device Format to format the newly
installed SD card;
2. Check to see whether video channel is closed or not, whether set
a timer recording or not, it will not take video when it is not
within the video recording time period.
3.Check the SD card inserting status and whether the SD light on
front panel is on or not.
Q: The video file is missing or there is no video file within a
certain period of time, how to do?
A: 1. Determine the time period by analyzing the final video file
before missing and the first video file after recovery.
2. Confirm whether the host is not on during that period of time,
such as when the driver halfway parking, loading and unloading
goods while the host is not set by video delay.
Q: When car PTZ cannot be controlled, it cannot rotate up and down,
how to do?
A: Check whether PTZ protocols and baud rate are set correct,
address codes are corresponding or not, whether have selected to
maximize the video of the channel when control the PTZ, for
example, when control the second channel, it must maximize the
screen of the second channel image to control it.GPS-related issues
Q: GPS module exists but no coordinate information?
A: 1.Check whether GPS module exists, if it does not exist, check
whether the hardware is installed or in a good contact.
2.Make sure that the GPS antenna contacts are good, whether the
antenna is broken, it is recommended to be located in places with
strong signal, note that some car glass shielding film will block
3 If the test is in the room, the signal of GPS antenna in the room
will be obscured, it is recommended that the GPS antenna is placed
Q: Deviation of GPS location on map?
A: It means the signal is valid if the GPS module already
positioned, there may many reasons for the deviation, such as
government restrictions, permissible error, GPS signal
interruption, etc; the actual satellite map may have deviation for
security reasons, general map can solve the problem by using GPS
correction.3G wireless module
Q: If use the 3G wireless module for dial-up, what do I need to pay
A: 1. Choose the built-in wireless module WCDMA or EVDO,
corresponding module settings are not the same, the modules
supported by different machines models are not the same, so please
make sure whether your module and SIM is in correspondence. Do not
use telecom SIM card on WCDMA machine;
2.Check whether the settings of Server IP and port are correct,
whether 3G signal is strong enough for dialing, and then check
whether the 3G dial-up is successful or not.
3. When dialing is unsuccessful, please check 3G antenna is in good
contact or not, the dial up may fail because of weak signal,
moreover, please check whether the SIM card has enough traffic, if
no traffic, dial-up will be unsuccessful.
Q: When 3G has neither report nor video , what should be done
A: Press INFO key to enter the system information page, check
whether the SIM card exists and view the signal strength as well as
dial-up status, whether the antenna is in good contact, and then
check the SIM to see whether it is out of traffic, the most basic
judgment is to replace the SIM card. If the dial up failed with
signal, then check whether the settings of center number and the
port are correct. Moreover check whether the device number of the
product is already occupied.
Q: 3G signal is intermittent, video is jammed?
A: At present the signal coverage of WCDMA and EVDO is rather wide,
however, there are some mountainous districts without signal
coverage, and some suburban areas have weak signal due to the local
network constraints, then it will be jammed during watching of
video, or video cannot be watched at all, the greatest impact of
this situation is from the local network; Moreover check whether
the frame rate setting of sub-stream is too high, because the video
may also occur such situation when the network is poor and frame
rate setting is high.
Q: Why the vehicle and video cannot be seen in CMSviewer client
when the device has been started?
A: At first make sure the central registration server is switched
on and on the net, then check whether the host device number has
been occupied to cause conflict, secondly check whether the
settings of server-centric IP and port are correct; devices report
to the center via the built-in 3G module or via WIFI. If via
built-in 3G, please check whether selected the correct type of
built-in 3G module, for example, WCDMA and EVDO module needs the
support from corresponding SIM card, check whether the antenna is
in good contact; If it still can not report when above all are
checked, enter into the system information page to view dial-up. If
dial-up is not successful, look up whether the setting of data
access point and center number is correct. If all ultimately fail,
please collect as much information as possible to submit to the
technical supporting staff for analysis, the more data provided,
the more convenient for technicians to solve the problem.
Q: The device is online, but why can I not see the video image?
A: Please set lower sub-stream to transmit image, the blocked or
slow transmission speed situation may occur when the sub-stream
frame rate is set very high and be affected by network uploading
limit; poor network signal or intermittent will seriously affect
the video transmission.
Q: The device is properly reported on CMSviewer, but the videos
cannot be seen after using for some time?
A: Firstly check whether the host side displays dialing, if it
keeps the dialing status, it may be because the flow of the SIM
card has run out, replace the SIM card to test; Secondly query
whether the host device number has been modified by the driver, the
host with modified device number needs to be resubmitted to add
vehicle information; thirdly, if it still does not work by changing
the card, it will need to check whether the host’s 3G module fails.